The KIP 7970 has two Sleep Modes to reduce the power consumption.

The KIP 7970 will enter Sleep Mode after a certain period of inactivity.

In the default setting;

• Warm Sleep Mode will start after a 15 minute of inactivity in order to reduce the power

supply for Fuser Unit.

• Cold Sleep Mode will start after a 60 minute of inactivity to stop the power supply for Fuser

Unit and some other components.

Sleep Mode is canceled and the machine gets ready when;

• the machine receives a print job through the network.

• an original is inserted into a KIP Scanner (option).

• you tap on the UI screen.

 Replace an Imaging Unit

NOTE: The Print Cartridge (toner) is a Customer Replaceable Unit (CRU). The machine will display a message on the Touch Screen when the Print Cartridge needs to be reordered. This message is a warning that the cartridge is nearing the end of its capacity. Only replace the Print Cartridge when a message is displayed prompting to do so.

To replace the Print Cartridge:

1. Remove any paper from the Bypass Tray located on the front of the machine. 
   
   
    
2. Fold the Bypass Tray extension to the closed position.
   
   
    
3. Lift the Bypass Tray into the closed position and make sure that the tray is securely closed.
   
   
    
4. Press on the release latches on the upper, left and upper, right sides of the Front Cover, and then open the Front Cover.
   
   
   
   
    
5. Grasp the handle on the Print Cartridge and pull straight out to remove the cartridge from the machine.
   
   
   
   
   
   NOTE: Follow the instructions that are packed with the new Print Cartridge to dispose of the used Print Cartridge as normal office waste, or recycle it in accordance with local regulations.
    
6. Before removing the packaging from the new Print Cartridge, shake it well to distribute the Toner (Dry Ink).
7. Remove the new Print Cartridge from its packaging, and then insert the cartridge into the machine. Make sure to align the cartridge properly with the inside of the machine, and make sure that it is fully seated.
   
   
   
   
    
8. Close the Front Cover.
   
   
    
9. Select the [Confirm] button on the Touch Screen.
   
   NOTE: If the Print Cartridge has been replaced following a "Replace Print Cartridge" message on the Touch Screen, the machine will assume the Toner Cartridge is new and will reset the Toner Usage Counters and messages. 
   
   If, however, a new Print Cartridge has been installed without a "Replace Print Cartridge" message being displayed, the Toner Usage Counters will need to be reset manually.

Solution : Calibrate the Control Panel

Solution : Clean the Laser Lenses

A vulnerability has been discovered in the OpenSSL cryptographic software version 1.0.1 to 1.0.1f widely used across the Internet for banking, investment, medical and other encrypted network traffic. The Heartbleed OpenSSL vulnerability works by allowing the certificate checking to be corrupted and traffic across a network to be monitored and some have called eavesdropping. Below are updates by Xerox and Kip regarding their exposure to the Heartbleed bug. Once I get information from Canon and Sharp, I will update the post.

In early April 2014, KIP was advised of the vulnerability known as Heartbleed in an open-source and widely-used Secure Socket Layer toolkit (OpenSSL). The vulnerability allows unauthenticated access to portions of the computer system memory. The code defect has acquired a substantial amount of media attention due to the ease with which the defect can be exploited and the potential exposure to sensitive information.

KIP is pleased to announce that all KIP Print and Scan systems including:

·         KIP Print Controllers (PPEC/IPS/KS8)

·         KIP Software & Applications

·         KIP Drivers

are not affected by this vulnerability.

The information below contains products that Xerox currently sells and some that they have recently stopped selling. If your product is not listed, it is probably older and therefore would have a version of OpenSSL that is not susceptible to Heartbleed. The vulnerable version of OpenSSL was published on April 19, 2002. If you acquired a Xerox device prior to that, you should be fine.

NOTE: The WorkCentre will indicate when it is time to order a new cartridge (if enabled) and when to replace the cartridge.

A message will be displayed if the SMart Kit Drum Cartridge Reorder Notification is enabled. This message is a warning that the cartridge is nearing the end of its life and a new cartridge should be ordered, unless a new cartridge is already available at the site.

The SMart Kit Drum Cartridge can be recycled; follow the disposal instructions received with the new cartridge.

1. Move the Bypass Tray Extension to the closed position.
   
   
    
2. Lift the Bypass Tray into the closed position and make sure the tray is securely closed.
   
   
    
3. Open the right Side Cover, by grasping the top handle on the right side of the WorkCentre and pulling down. The inside of the WorkCentre will be accessible.
   
   
   
   CAUTION: The Side Cover must remain in the open position until after the SMart Kit Drum Cartridge is inserted into the WorkCentre. The SMart Kit Drum Cartridge cannot be properly installed when the Side Cover is closed.
    
4. Open the Front Cover by grasping the top, right handle and pulling down. Wordless (icon) instructions for replacing the Toner Cartridge and SMart Kit Drum Cartridge can be found on the inside of the Front Cover. 
   
   
   
   WARNING: Remove the Toner (Dry Ink) Cartridge before attempting to remove the SMart Kit Drum Cartridge.
    
5. Rotate the colored locking lever to the right, to unlock the cartridge.
   
   
    
6. Lift the colored latch to release the Toner Cartridge and remove the used cartridge by pulling it towards you.
   
   
    
7. Set the Toner Cartridge aside; placing it on a surface covered with scrap paper or similar material.
   
   NOTE: Hold the empty SMart Kit Drum Cartridge away from you to avoid spilling any Toner residue.
   
   The instructions packaged with the new SMart Kit Drum Cartridge will indicate how to properly dispose of the used cartridge.
    
8. Squeeze the retaining clip between your thumb and forefinger, and then pull the used SMart Kit Drum Cartridge toward you to remove it from the WorkCentre. 
   
   
   
   Place the used cartridge on a few sheets of scrap paper.
9. Unpack the new SMart Kit Drum Cartridge.
10. Remove the protective paper by lifting it off the top of the cartridge.
11. Remove the seal tape by pulling on the red tag attached to the cartridge.
    
    
     
12. Holding the SMart Kit Drum Cartridge by the handle on top of the cartridge, align the cartridge with the grooves on the frame, and then slide the cartridge into the WorkCentre. A click will be heard when the cartridge is properly installed.
    
    
     
13. Re-install the Toner Cartridge by lining up the top left and right edges of the cartridge with the grooves at the top of the cartridge slot, then slide the cartridge fully into the slot.
    
    
    
    
     
14. Rotate the locking lever to the left, to lock the cartridge in place.
    
    
    
    NOTE: If after installing the Toner Cartridge the Front Cover will not close, check that the Toner Cartridge is positioned and latched correctly.
     
15. Lift the Front Cover to close it.
16. Lift the right Side Cover to close it.
17. Select the [Confirm] button to confirm that a new cartridge has been installed. The SMart Kit Drum Cartridge counter will automatically be reset.

Canon U.S.A. Announces Mobile Printing App for Home and Office Users

New App for iPhone^® and iPad^® Enables Efficient, Intuitive Mobile Printing to a Wide Range of Canon Devices Including select imageCLASS Printers, imageRUNNER ADVANCE and imageRUNNER Office Systems and imageRUNNER LBP Printers 

LAKE SUCCESS, N.Y., November 26, 2012 – Canon U.S.A., Inc., a leader in digital imaging solutions, today announced its Canon Mobile Printing App for iPhone^® and iPad^®, extending Canon's already comprehensive support for mobile office users and consumers. Canon Mobile Printing enables users in homes and offices of all sizes to send print jobs directly from their iPhone and iPad to a compatible Canon output device.

The Canon Mobile Printing App is compatible with select Canon imageCLASS desktop laser printers and multifunction printers including the recently launched MF4000 models. The app is also compatible with Canon's recently released next generation imageRUNNER ADVANCE C5200, 6200, and 8200 enterprise multifunction office systems. Additionally, the app supports most imageRUNNER and imageRUNNER ADVANCE enterprise multifunction office systems, as well as imageRUNNER LBP printers. Users can print Microsoft^® Office files (doc, docx, xls, xlsx, ppt, pptx), iWork^® files (Pages, Numbers, Keynote), JPEG, GIF, BMP, PNG, TIFF and PDF files, photographs (stored in Photo Albums and taken with the device camera), and web pages directly through the app's user-friendly interface.

"With today's mobile workforce, being able to print on-the-go is becoming an increasingly valuable asset," said Sam Yoshida, vice president and general manager, Marketing, Business Imaging Solutions Group, Canon U.S.A. "The new Canon Mobile Printing App provides ease of use and places traditional print functionality at the fingertips of today's mobile worker."

The Canon Mobile Printing App features the following innovative tools:

The Canon Mobile Printing user experience becomes seamless with the integration of OpenIn, a feature that allows users to capitalize on the functionality of the mobile app while navigating through files located elsewhere. The OpenIn feature allows users to easily navigate to Canon Mobile Printing directly from the application they are in, giving the customer more ways to access printing.

Designed with the end-user in mind, the app supports a variety of file formats. Users can print Microsoft Office files (doc, docx, xls, xlsx, ppt, pptx), iWork files, PDF, JPEG, GIF, BMP, PNG, TIFF files, photographs, and web pages can be printed directly through the app.

The app supports devices running iOS 5.1 - 6.0 and is available for the iPhone 5, iPhone 4S, iPhone 4, the new iPad, iPad 2, and the original iPad. The app also supports most imageRUNNER and imageRUNNER ADVANCE enterprise multifunction office systems and includes support for the next generation imageRUNNER ADVANCE multifunction devices. In addition, the app supports compatible imageCLASS printers and imageRUNNER LBP printers.

The app can search for and identify Canon printers within a wireless (Wi-Fi) broadcast range - and automatically save these devices for future use. If the Canon printer cannot be found within a wireless broadcast range, users can manually enter the IP address of the Canon device to list it as one of their available print devices.

The app offers a variety of built-in printing options to enhance control and performance. Users can tailor print range, paper size, color output, and number of copies directly from the app. Depending on the finishing features on the printer, documents can also be stapled directly from the menu. Additionally, users can instruct the app to feed paper automatically or via the device manual bypass.

Users will be able to preview documents, photos and web pages prior to printing to determine the ideal settings for a specific print job. Items with multiple pages can also be previewed by swiping the screen to move through the document.

The Canon Mobile Printing App is available for free from the App Store^℠ or atwww.itunes.com/appstore. Search for "Canon Mobile Printing".